Ameritec 30-0056 Interface
Manufacturer:
Model:
30-0056
Date:
2000
Class:
Type:
SubType:
AM8e E&M Adapter
Information
The Model 300056
AM8e E&M Adapter is physically designed to
replace the front
cover of the Call
Analyzer. The illustration on the cover of
this manual shows both
units as they would be set up for use.
Note: F or brevity, the Model 300056
AM8e E&M Signaling
Adapter will be referred
to as the "E&M Adapter".
The E&M Adapter is electrically connected to the Call
Analyzer via a ribbon cable
from a "TO AM8e" connector on its front panel to the
LINE/TIMS connector on the
rear panel of the Call
Analyzer. All power and PCM2 input
and output connections
between the E&M Adapter and the Call
Analyzer are via this
connector.
The interfaces between the E&M signaling and VF circuits are
via bantam jacks on
the front panel of the E&M Adapter.
Functionally, the E&M Adapter is an Analog to
Digital/Digital to Analog signal
converter, which converts an E&M Signal from its line or
equipment
Interface at a
Central Office, to 2.048Mbps PCM Rx and Tx Signals, which
are processed by the
Call
Analyzer. This allows the Call
Analyzer to Emulate or
Monitor either the
near-end (Tx) or far-end (Rx) signaling on an E&M
Interface.
The user must select
PCM2 as PCM input.
Manual type:
User Manual
Pages:
30
Size:
994.92 Kbytes (1018795 Bytes)
Language:
english
Revision:
C
Manual-ID:
18-0044
Date:
2000 10 18
Quality:
Electronic document, no scan, very well readable.
Upload date:
2017 10 14
MD5:
3bd77d2cc970418d5f63db1c329f83b5
Downloads:
451
Information
This manual is intended for use with the
Ameritec Model
300056
AM8e E&M
Adapter (P/N 300056). This manual should be used in
conjunction with the AM8e
PCM/VF Call
Analyzer Instruction Manual (P/N 180035), and
the
AM8e Protocol Table
Development Guide (P/N 180040).
This manual is divided into 4 major sections, as listed in
the Table of Contents.
This first introductory section provides an overview of the
AM8e VF Call
Analyzer,
AM8e E&M Signaling Adapter, and Protocol Table Development
Guide; all of which are
of fundamental importance to the instructions in this manual.
The second section describes the Model 300056
AM8e E&M
Adapter, its front panel,
and connections.
The third section is an overview of the characteristics of
the various E&M
connections and signaling types.
1.
INTRODUCTION ... 1
1.1
Ameritec AM8e PCM/VF Call
Analyzer
... 1
1.2
AM8e Model 300056 E&M Adapter
... 2
1.3
AM8e Protocol Table Development Guide and
Disk ... 2
1.4 Overview of E&M Test Configuration
... 3
2. OPERATION OF THE E&M ADAPTER
... 4
2.1 Front Panel Controls and
Indicators ... 4
2.1.1 PWR ON/OFF (Power ON/OFF
Switch) ... 5
2.1.2 MODE (Mode Selector Switch)
... 5
2.1.3 MODE Indicators (Mode-Selected Indicators)
... 5
2.1.4 TYPE (E&M Type-Select Switch)
... 5
2.1.5 TYPE Indicators (E&M Type Indicators)
... 5
2.1.6 CONNECTION (Connection-Type Switch)
... 6
2.1.7 CONNECTION Indicators (Connection-Type Indicators)
... 6
2.1.8 E1/M1, and E2/M2 Indicators (Active Status of E&M
Signals) ... 6
2.2 Connection to the Call
Analyzer ... 6
2.2.1 TO
AM8e /
AM8e Interface
Connection) ... 6
2.3 Connections to Test
Leads ... 7
2.3.1 SB/SG Connection
... 8
2.3.2 Tx/Rx for
E1/M1 ... 8
2.3.3 Tx/Rx for
E2/M2 ... 9
2.3.4 A1/B1 VF Connector
... 9
2.3.5 A2/B2 VF Connector
... 9
2.3.6 CO Ground
Terminal ... 9
2.4 Setting the Operating Conditions
...
10
2.5 Remote Control of E&M
Adapter ...
12
2.5.1 Remote Setup (ADP
Command) ...
12
2.5.2 Remote Status (RADP Command)
...
13
2.6 Call
Analyzer Display and Bit Indicators
...
13
3. E&M SIGNALING DESCRIPTION
...
14
3.1 Connection Types
...
15
3.1.1 2-wire E&M
...
16
3.1.2 4-wire E&M
...
16
3.1.3 4-wire E&M2
...
16
3.1.4 Phantom E&M
...
16
3.2 E&M Trunk
Types ...
18
3.2.1 E&M TYPE I
...
18
3.2.2 E&M TYPE II
...
18
3.2.3 E&M TYPE III
...
19
3.2.4 E&M TYPE
IV ...
20
3.2.5 E&M TYPE
V ...
20
APPENDIX
A ...
22
A.1 Analog R2 Monitoring in
AM8e ...
22
Comments