Epson - EPL-N4000 - Printer
Manufacturer:
Equipment:
EPL-N4000
Date:
1998
Category:
Group:
Sub Group:
Information
Features
EPL-N4000 N4000+ is non-impact page
Printer applied with
laser xerographic method.
ENGINE FEATURES_
□ High speed & high reliability A3 engine.
□ Resolution:600 dpi
□ Printing speed:40 ppm (A4) / 40ppm (Letter)
□ Standard paper feeders are two universal cassettes (500
sheets x2) and manual feed tray (50 sheets)
□ Options: large-capacity paper unit (500 sheets(A4 to A3)
on MP tray + 1000 sheets on cassette 1 + 1000 sheets (A4,
Letter, and Executive sizes) on cassette 2)
Refer to Table 1-6, "Feeding Method," on page 10 for details.
□ Offset stacking equipped as standard
□ Wide range of options (Duplex Module, Face-up tray,
Envelope Feeder, Multibin Unit, Finisher Stapler*, HDD*)
NOTE: Finisher Stapler and HDD are only supported from
EPL-N4000+. Refer to Table 1-2 on page 4 for support range.
CONTROLLER FEATURES_
□ High speed controller, employing new CPU 64-bit RISC CPU
VR4700 133MHz
□ SDRAM DIMMs adopted
64MB RAM equipped as standard
Expandable up to 256 MB (using commercially available SDRAM
DIMMs) However, 256MB SDRAM DIMMs cannot be used.
□ Two standard interfaces IEEE 1284 parallel interface
Ethernet interface (100Base-TX)
□ 1 slot for Type B interface
Type B Level 3 is supported from EPL-N4000+.
□ Enhanced Micro Gray loaded
Service manual
Manual type:
Service manual
Pages:
195
Size:
9.6 MB
Language:
english
Revision:
A
Manual-ID:
Date:
January 1998
Quality:
Electronic document, no scan, very well readable.
Upload date:
April 17, 2017
MD5:
f49d31a2-745f-ff96-a028-fbf66da74e8a
Downloads:
854
Last month downloads:
7
Information
This manual describes basic functions, theory of electrical
and mechanical operations, and repair procedures of
EPL-N4000 N-400+ Optional
Finisher Stapler. The instructions and procedures included
herein are intended for the experienced repair technicians,
and attention should be given
to the precautions on the preceding page.
Contents
This manual consists of three chapters and Appendix.
CHAPTER 1. PRODUCT DESCRIPTIONS
Provides a general overview and specifications of the
product.
CHAPTER 2. OPERATING PRINCIPLES
Describes the theory of electrical and mechanical
operations of the product.
CHAPTER 3. DISASSEMBLY AND ASSEMBLY
Describes the step-by-step procedures for
disassembling and assembling the product.
APPENDIX Provides the following additional information for
reference:
• Connector pin assignments
• Electric circuit boards components layout
• Exploded diagram
Service manual
Manual type:
Service manual
Pages:
306
Size:
11.8 MB
Language:
english
Revision:
B
Manual-ID:
SEPG98002
Date:
September 1999
Quality:
Electronic document, no scan, very well readable.
Upload date:
April 17, 2017
MD5:
b7ed048b-d70a-7757-cb47-64f719949bdf
Downloads:
1006
Last month downloads:
6
Information
This manual describes basic functions, theory of electrical
and mechanical operations, maintenance and repair procedures
of
EPL-N4000 N4000+.
The instructions and procedures included herein are intended
for the experienced repair technicians, and attention should
be given to the precautions
on the preceding page.
This manual consists of six chapters and Appendix.
CHAPTER 1. PRODUCT DESCRIPTIONS
Provides a general overview and specifications of the
product.
CHAPTER 2. OPERATING PRINCIPLES
Describes the theory of electrical and mechanical
operations of the product.
CHAPTER 3. TROUBLESHOOTING
Provides the step-by-step procedures for the
troubleshooting.
CHAPTER 4. DISASSEMBLY AND ASSEMBLY
Describes the step-by-step procedures for
disassembling and assembling the product.
CHAPTER 5. ADJUSTMENTS
Provides
Epson approved methods for adjustment.
CHAPTER 6. MAINTENANCE
Provides preventive maintenance procedures and the
lists of
Epson approved lubricants and adhesives
required for servicing the product.
APPENDIX Provides the following additional information for
reference:
• Connector pin assignments
• Electric circuit boards components layout
• Exploded diagram
• Electrical circuit boards schematics