Philips - PM 2813 - Power Supply
Manufacturer:
Image 1 of 1
If you have any other photos or manuals for the
Philips PM 2813
you can
upload the files here.
Equipment:
PM 2813
Date:
1992
Category:
Group:
Sub Group:
2 Manuals
Service manual
Manual type:
Service manual
Pages:
28
Size:
1.4 MB
Language:
english
Revision:
Manual-ID:
4822 872 80169 920305
Date:
Quality:
Scanned document, all readable.
Upload date:
Nov. 21, 2008
MD5:
00b780e2-0f2b-29a5-641b-6317e3ef07d8
Downloads:
6494
Information
Info only for the Programming Card
Service manual
Manual type:
Service manual
Pages:
66
Size:
17.2 MB
Language:
english
Revision:
Manual-ID:
4822 872 85004
Date:
December 1991
Quality:
Scanned document, all readable.
Upload date:
July 31, 2020
MD5:
02436219-453c-5e53-18fc-d4d1233de850
Downloads:
1337
Information
1 SAFETY INSTRUCTIONS...1-1
1.1 INTRODUCTION...1-1
1.2 SAFETY PRECAUTIONS...1-1
1.3 CAUTION AND WARNING STATEMENTS...1-1
1.4 SYMBOLS...1-1
1.5 IMPAIRED SAFETY...1-2
1.6 GENERAL SAFETY INFORMATION...1-2
2 GENERAL INFORMATION...2-1
2.1 CHARACTERISTICS...2-1
2.1.1 Performance Characteristics...2-1
2.1.2 Environmental Characteristics...2-1
2.1.3 Mechanical requirements...2-1
2.1.4 Instrument performance...2-2
2.1.4.1 Output channel 30V/10A/60W performance...2-2
2.1.4.2 Output channel 60V/5A/60Wperformance...2-4
2.1.4.3 Output channel 60V/10AJ120Wperformance...2-5
2.1.5 Safety characteristics...2-7
2.1.6 Dimensions and weight...2-8
2.1.7 Mains Supply Conditions...2-8
2.2 INTERFERENCES...2-8
2.2.1 Electromagnetic interference...2-8
2.2.2 Frequency interference...2-8
3 CIRCUIT DESCRIPTIONS...3-1
3.1 DESCRIPTION OF EACH CIRCUIT SECTION...3-1
3.1.1 CPU PCB, unit A1 ...3-1
3.1.2 DISPLAY KEYBOARD PCB, unit A2...3-5
3.1.3 AD-DA PCB, unit A3...3-5
3.1.4 Output on the front panel...3-9
3.1.5 Input module...3-10
3.1.5.1 Setting the power voltage...3-10
4 PERFORMANCE VERIFICATION PROCEDURES...4-1
4.1 GENERAL INFORMATION...4-1
4.2 RECOMMENDED TEST EQUIPMENT...4-1
5 DISASSEMBLING THE INSTRUMENT...5-1
5.1 GENERAL INFORMATION...5-1
5.2 REMOVING THE COVER...5-1
5.3 DISASSEMBLING THE INSTRUMENT...5-1
5.4 REASSEMBLING THE INSTRUMENT...5-2
6 CALIBRATION ADJUSTMENT PROCEDURE...6-1
6.1 GENERAL INFORMATION...6-1
6.1.1 Recommended test equipment for local calibration...6-1
6.1.2 Recommended test equipment for remote calibration...6-1
6.2 CALIBRATION PROCEDURES...6-1
6.2.1 Local calibration procedure...6-1
6.2.2 Remote calibration procedure...6-4
7 CORRECTIVE MAINTENANCE PROCEDURES...7-1
7.1 HARDWARE-ERROR MESSAGES...7-1
7.2 TROUBLESHOOTING...7-2
7.2.1 Introduction...7-2
7.2.2 CPU PCB...7-2
7.2.3 AD-DA PCB...7-3
7.3 REPLACEMENTS...7-3
7.3.1 Standard parts...7-3
7.3.2 Special parts...7-4
7.3.3 Transistors and integrated circuits...7-4
7.4 RECALIBRATION AFTER REPAIR...7-4
7.5 INSTRUMENT REPACKING...7-4
8 SAFETY INSPECTION AND TESTS AFTER REPAIR AND MAINTENANCE IN THE PRIMARY CIRCUIT...8-1
8.1 GENERAL DIRECTIONS...8-1
8.2 SAFETY COMPONENTS...8-1
8.3 CHECKING PROTECTIVE GROUND...8-1
8.4 CHECKING INSULATION RESISTANCE...8-1
8.5 CHECKING LEAKAGE CURRENT...8-1
8.6 VOLTAGE TEST...8-1
9 PARTS LIST...9-1
10 WIRING DIAGRAM 10-1