Volume 1 This Operating Manual consists of 2 volumes Volume 1 Data Sheet Safety Instructions Certificate of Quality EU Certificate of Conformity List of R&S Representatives Manuals for Spectrum Analyzer FSP Tabbed Divider 1 Chapter 1: Putting into Operation 2 Chapter 2: Getting Started 3 Chapter 3: Operation 4 Chapter 4: Functional Description 10 Chapter 10: Index Operating Manual FSP The operating manual describes the following models and options of spectrum analyzer FSP: • FSP3 9 kHz to 3 GHz • FSP7 9 kHz to 7 GHz • FSP13 9 kHz to 13.6 GHz • FSP30 9 kHz to 30 GHz • FSP40 9 kHz to 40 GHz • • • • • • • • Option FSP B3 Option FSP-B4 Option FSP-B9 Option FSP-B10 Option FSP-B15 Option FSP-B16 Option FSP-B25 Option FSP-B28 audio demodulator OCXO - reference oscillator tracking generator external generator control pulse calibrator LAN interface electronic attenuator trigger port This operating manual contains information about the technical data of the instrument, the setup functions and about how to put the instrument into operation. It informs about the operating concept and controls as well as about the operation of the FSP via the menus and via remote control. Typical measurement tasks for the FSP are explained using the functions offered by the menus and a selec- tion of program examples. Additionally the operating manual includes information about maintenance of the instrument and about error detection listing the error messages which may be output by the instrument. It is subdi- vided into 9 chapters:

Volume 2 This Operating Manual consists of 2 volumes Volume 2 Data Sheet Safety Instructions Manuals for Spectrum Analyzer FSP Tabbed Divider 5 Chapter 5: Remote Control – Basics 6 Chapter 6: Remote Control – Commands 7 Chapter 7: Remote Control – Program Examples 8 Chapter 8: Maintenance and Hardware Interfaces 9 Chapter 9: Error Messages 10 Chapter 10: Index Operating Manual FSP The operating manual describes the following models and options of spectrum analyzer FSP: • FSP3 9 kHz to 3 GHz • FSP7 9 kHz to 7 GHz • FSP13 9 kHz to 13.6 GHz • FSP30 9 kHz to 30 GHz • FSP40 9 kHz to 40 GHz • • • • • • • • Option FSP B3 Option FSP-B4 Option FSP-B9 Option FSP-B10 Option FSP-B15 Option FSP-B16 Option FSP-B25 Option FSP-B28 audio demodulator OCXO - reference oscillator tracking generator external generator control pulse calibrator LAN interface electronic attenuator trigger port This operating manual contains information about the technical data of the instrument, the setup functions and about how to put the instrument into operation. It informs about the operating concept and controls as well as about the operation of the FSP via the menus and via remote control. Typical measurement tasks for the FSP are explained using the functions offered by the menus and a selec- tion of program examples. Additionally the operating manual includes information about maintenance of the instrument and about error detection listing the error messages which may be output by the instrument. It is subdi- vided into 9 chapters:

Quick Start Guide Contents Safety Instructions Certificate of Quality Support Center Adress List of R&S Representatives 1Front and Rear View .............................................................................. 1.1 Front view....................................................................................................................1.2 Function Keys on the Front Panel.............................................................................1.4 Rear View ....................................................................................................................1.6 Spectrum Analyzers Connections.............................................................................1.8 Front Panel of the Instrument ...................................................................................1.8 Rear Panel of the Instrument..................................................................................1.10 2Putting into Operation........................................................................... 2.1 Putting into Operation ................................................................................................2.2 Unpacking the Instrument.........................................................................................2.2 Setting Up the Instrument .........................................................................................2.3 Installation in a 19" rack............................................................................................2.3 Connecting the Instrument to the AC Power Supply.................................................2.4 Switching on the R&S FSP .......................................................................................2.4 Functional Test .........................................................................................................2.5 Switching Off the R&S FSP ......................................................................................2.5 Connecting Peripheral Devices .................................................................................2.6 Connecting an External Keyboard ............................................................................2.6 Connecting a Mouse.................................................................................................2.6 Connecting an External Monitor ...............................................................................2.7 Connecting a Printer.................................................................................................2.7 Connecting USB Devices (e.g. a Power Meter)........................................................2.8 Connecting External Generators ............................................................................2.10 Connecting the R&S FSP to the Generator ..................................................2.11 Configuring the Generator on the R&S FSP .................................................2.12 Activating the Generator Configuration and Setting the Output Level...........2.13 Using an External Generator as a Tracking Generator .................................2.14 R&S FSP Setup .........................................................................................................2.15 Selecting the Frequency Reference .......................................................................2.15 Setting the Date and Time ......................................................................................2.15 Setting the IEC Bus Interface................................................................................. 2.16 IEC Bus Address.......................................................................................... 2.16 IEC Bus Language ....................................................................................... 2.17 ID Response String ...................................................................................... 2.18 Setting the Screen Colours .................................................................................... 2.18 Automatically Switching Off the Internal Screen .................................................... 2.19 Selecting and Configuring Printers......................................................................... 2.20 Selecting Alternative Printer Configurations ................................................. 2.22 Selecting Printer Colours.............................................................................. 2.22 Installing Plug&Play Printers .................................................................................. 2.23 Installing Non-Plug&Play Printers .......................................................................... 2.23 Configuring the LAN Interface (only with Op R&S FSP-B16) ............................... 2.24 Connecting the Instrument to the Network ............................................................. 2.24 Configuring the Network Card................................................................................ 2.24 Installation von Treibern ............................................................................... 2.24 Configuring the Interface .............................................................................. 2.25 Configuring Existing Network Protocols (TCP/IP Protocol) .......................... 2.26 Installing Additional Network Protocols and Services................................... 2.29 Operating System Properties .................................................................................. 2.30 Properties Specific to Windows XP ........................................................................ 2.30 Windows-XP Service Packs ......................................................................... 2.31 Opening the Windows XP Start Menu .......................................................... 2.31 Windows XP Software Approved for the Instrument..................................... 2.31 3 Firmware-Update and Installation of Firmware Options ..................... 3.1 Firmware Update ........................................................................................................ 3.2 Activating Firmware Options .................................................................................... 3.3 4 Brief Introduction................................................................................... 4.1 Diagram Layout .......................................................................................................... 4.2 Displays in the Diagram Area ......................................................................... 4.3 Setting Parameters..................................................................................................... 4.7 The Keypad.............................................................................................................. 4.7 The Rotary Knob and Cursor Keys .......................................................................... 4.8 Editing Numeric Parameters .................................................................................... 4.8 Editing Alphanumeric Parameters............................................................................ 4.9 Help Line Editor Type 1:................................................................................. 4.9 Help Line Editor Type 2:............................................................................... 4.10 5 Introduction ........................................................................................... 5.1 Measuring a Sinusoidal Signal ..................................................................................5.2 Measuring the Level and Frequency with Markers ...................................................5.2 Procedure .......................................................................................................5.2 Increasing the Frequency Resolution .............................................................5.3 Setting the Reference Level............................................................................5.4 Measuring the Signal Frequency using the Frequency Counter ...............................5.5 Measuring Harmonics of Sinusoidal Signals ...........................................................5.7 Measuring the Suppression of the First and Second Harmonic of an Input Signal..............................................................................................................5.7 Reducing Noise ..............................................................................................5.8 Measuring Signal Spectra with Multiple Signals....................................................5.11 Separating Signals by Selecting the Resolution Bandwidth ...................................5.11 Separating Two Signals with a Level of –30 dBm each at a Frequency Spacing of 30 kHz.........................................................................................5.11 Measuring the Modulation Depth of an AM-Modulated Carrier in the Frequency Domain .......................................................................................5.15 Measurements in the Time Domain.........................................................................5.16 Measuring the Power Characteristic.......................................................................5.16 Example – Measuring the Power of a GSM Burst During the Activation Phase. ........................................................................5.16 Measuring the Power Characteristic of Burst Signals.............................................5.18 Example - Measuring the Edges of a GSM Burst with High Time Resolution...5.18 Measuring the Signal-to-Noise Ratio of Burst Signals ............................................5.20 Example - Signal-to-Noise Ratio of a GSM Signal........................................5.20 Measurement of AM-Modulated Signals.................................................................5.23 Example 1 – Displaying the AF of an AM-Modulated Signal in the Time Domain ..........................................................................5.23 Measurement of FM-Modulated Signals.................................................................5.25 Example - Display of the AF of an FM-Modulated Carrier.............................5.25 Storing and Loading Instrument Settings ..............................................................5.28 Storing an Instrument Configuration (without Traces) ............................................5.28 Storing Traces ..............................................................................................5.29 Loading an Instrument Configuration......................................................................5.30 Automatic Loading of a Data Record during Booting ....................................5.31 Printing Out the Measurement Results...................................................................5.32 Selecting the Colour Setting for the Printout...........................................................5.32 Additional Measurement Examples ........................................................................5.33 6R&S FSP Brief Introduction to Remote Control................................................... 6.1 Basic Steps in IEC Bus Programming...................................................................... 6.2 Linking the IEC Bus Library for Visual Basic ............................................................ 6.2 Initialization and Default State.................................................................................. 6.3 Creating Global Variables .............................................................................. 6.3 Initializing the Controller ................................................................................. 6.3 Initializing the Instrument................................................................................ 6.3 Switching the Screen Display On and Off ...................................................... 6.4 Configuring the Power Save Function for the Display .................................... 6.4 Sending Simple Instrument Setting Commands....................................................... 6.5 Switching to Manual Operation ................................................................................ 6.5 Reading Out Instrument Settings ............................................................................. 6.6 Marker Positioning and Readout.............................................................................. 6.6 Command Synchronization ...................................................................................... 6.7 Reading Output Buffers.................................................................................. 6.7 Reading Error Messages................................................................................ 6.8 Detailed Programming Examples............................................................................. 6.9 Default Setting of the R&S FSP ............................................................................... 6.9 Setting the IEC Bus Status Registers............................................................. 6.9 Making Default Settings for Measurements.................................................. 6.10 Using Markers and Delta Markers.......................................................................... 6.11 Marker Search Functions, Restricting the Search Range............................. 6.11 Frequency Counting ..................................................................................... 6.13 Working with a Fixed Reference Point (Reference Fixed)............................ 6.14 Measuring Noise and Phase Noise .............................................................. 6.15 Reading Out Trace Data ........................................................................................ 6.16 Storing and Loading Instrument Settings ............................................................... 6.18 Storing Instrument Settings .......................................................................... 6.18 Loading Instrument Settings......................................................................... 6.19 Setting the Data Record for Startup Recall .................................................. 6.19 Configuring and Starting a Printout ........................................................................ 6.20 Appendix Appendix A: Printer Interface ................................................................................... A.1 Installing Non-Plug&Play Printers............................................................................ A.1 Local Printer................................................................................................... A.1 Network Printer .............................................................................................. A.6 Appendix B: LAN-Interface ....................................................................................... B.1 Installing Non-Plug&Play Printers .................................................................. B.1 Configuration Examples................................................................................. B.4 Subsequent Changes to the Network Configuration (computer name, domain, workgroup, etc) .................................................... B.5 Operating the Instrument without a Network............................................................ B.7 Operating the Instrument on the Network ................................................................ B.7 Creating Users...............................................................................B.7 Changing the User Password ........................................................................ B.9 NOVELL Network only: Configure NOVELL Client ...................................... B.11 Logging on to the Network ........................................................................... B.12 Deactivating the Automatic Login Mechanism ............................................. B.12 Reactivating the Automatic Login Mechanism ............................................. B.12 Using Network Drives .................................................................................. B.12 Printing on a Network Printer ....................................................................... B.15 Sharing Directories (only with Microsoft Networks)...................................... B.19 Remote Monitoring of the R&S FSP with XP Remote Desktop ............................. B.22 Introduction .................................................................................................. B.22 Configuring the R&S FSP for Use of Remote Desktop ................................ B.22 Configuring the Controller ............................................................................ B.25 Connection Setup with the R&S FSP........................................................... B.28 Interrupting and Restoring the Remote Desktop Connection with the R&S FSP ..................................................................................................... B.31 Deactivating the R&S FSP from the Controller ............................................ B.31 RSIB Protocol........................................................................................................... B.31 Appendix C: External Generator Control................................................................. C.1 List of Generator Types Supported by the R&S FSP............................................... C.1

Tabbed Divider Overview Index Safety Instructions Certificate of Quality Spare Parts Express Service List of R&S Representatives Contents of Manuals for Spectrum Analyzer FSP Service and Repair Tabbed Divider 1 Chapter 1: Performance Test 2 Chapter 2: Adjustment 3 Chapter 3: Repair 4 Chapter 4: Firmware Update / Installation of Options 5 Chapter 5: Documents Service Manual - Instrument The service manual - instrument informs on how to check compliance with rated specifications, on instrument function, repair, troubleshooting and fault elimination. It contains all information required for repairing the FSP by the replacement of modules. The service manual comprises four chapters and an annex (chapter 5) containing the FSP circuit docu- mentation: ChapterChapterChapterChapterChapter1 2 3 4 5 provides all the information necessary to check FSP for compliance with rated specifications. The required test equipment is included, too. describes the manual adjustment of the calibration source and of the frequency accuracy as well as the automatic adjustment of individual module data following module replacement. describes the design of FSP as well as simple measures for repair and fault diagnosis, in particular, the replacement of modules. contains information on the extension and modification of FSP by installing instrument software and retrofitting options. describes the shipping of the instrument and ordering of spare parts and contains spare parts lists and exploded views of FSP.