Amplifier Section [U.S. and Canadian models] Continuous average power output is 120 watts* per channel, min., at 8 ohms from 20 Hertz to 20,000 Hertz with no more than 0.003% total harmonic distortion. Continuous power output (both channels driven, measured by Audio Spectrum Analyzer) 20 Hz to 20 kHz, T.H.D. 0.005%, 40 . . . 170W + 170W 20 Hz to 20 kHz, T.H.D. 0.003%, 6Ω . . . 140W + 140W 20 Hz to 20 kHz, T.H.D. 0.003%, 8Ω . . . 120W + 120W [U.K. and other destination models] Continuous power output (both channel drivew, measured by Audio Spectrum Analyzer) 20 Hz to 20 kHz, T.H.D. 0.005%, 4Ω...........150W + 150W 20 Hz to 20 kHz, T.H.D. 0.003%, 8Ω...........120W + 120W DIN continuous power output (both channels driven) 1 kHz, T.H.D. 1%, 8Ω..............................150W + 150W 1 kHz, T.H.D. 1%, 4Ω..............................170W + 170W Power bandwidth 0.05%, 8Ω.................................................5 Hz — 60 kHz Damping factor (20 Hz to 20 kHz), 8Ω ...................................................60 Total harmonic distortion (measured by Audio Spectrum Analyzer) 20 Hz to 20 kHz, 120W, 8Ω ................................ 0.003% Input sensitivity/impedance PHONO (MM)...............................................2.5 mV/50 k$2 PHONO (MC) ...............................................0.25 ιγΛ//40Ω CD, TUNER, LINE, TAPE..........................150 mV/50 kO PHONO overload level 1 kHz, T.H.D. 0.01% (MM/MC)............... 200 mV/20 mV Output level/impedance TAPE REC, ADAPTOR OUTPUT.............150 mv/0.8k0 Frequency response PHONO (MM), 20 Hz to 20 kHz.......................±0.2 dB PHONO (MC), 20 Hz to 20 kHz .......................±0.3 dB CD, TUNER, LINE TAPE 1 Hz to 150 kHz + 0 dB Tone control (volume control set at -30 dB position) BASS........................................................±8 dB (100 Hz) TREBLE....................................................±8 dB (10 kHz) Loudness contour (volume control set at -30 dB position) + 5 dB (100 Hz)/+ 3 dB (10 kHz) Filter (SUBSONIC).....................................17 Hz (12 dB/oct.) Signal-to-Noise ratio (IHF short circuit, A network) PHONO (MM, 5 mV input/MC, 0.5 mV input) 95 dB/83 dB CD, TUNER, LINE, TAPE ....................................109 dB Signal-to-Noise ratio (DIN, continuous power/50 mW) PHONO (MM)...............................................74 dB/65 dB CD, TUNER, LINE, TAPE............................92 dB/66 dB DA Converter Section Data format..............................Digital audio interface format Digital coaxial Input/Output Rated input voltage/impedance.................0.5 Vp-p/750 Rated output voltage/impedance...............0.5 /ρ-ρ/75Ω Digital Optical Input/Output Rated Input Level..............................—26------18 dB m (<") Rated Output Level......................................—22 dB m (?mF) Audio Signal Distortion rate (1 kHz, 2 V).................................. 0.003% S/N (1 kHz, 2 V).......................................................98 dB Frequency characteristics (10-20 kHz) .............±0.5 dB Power Supply/Miscellaneous Power requirements U.S. and Canadian models ...................AC120V, 60 Hz U.K. model........................................a.c. 240V, 50/60 Hz Other destination models.............AC 110V/120 — 127V 220V/240V (switchable), 50/60 Hz Power consumption U.S. and Canadian models.................................... 670W, 820 VA U.K. model.............................................................. 1000W Other destination models...................................... 1000W Dimensions....................... 457(W) χ 475(D) x 173(H) mm 18(W) χ 18-11/16(D) χ 6-13/16(H) in Weight.....................................................29.2 kg (64 lb 6 oz) Accessories Operating instructions. 1 Specifications and design subject to possible modification without notice due to improvements. * Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Claims for Amplifiers.