.....obsolete user manuals, a lot of repair manuals, free service manuals, rare schematic diagrams, usefull service instructions, pdf books, how to repair instructions, lost operating manuals, old handbooks, tons of part lists, hidden service bulletins, your instruction books, informative repair tips, complete disassembly routines.....


What are you looking for?

extended search


Fluke 192 ScopeMeter
Manufacturer:
Model:
192
Date:
2000
Class:
Type:
SubType:
Scopemeter

Information

The Fluke 192/196/199 ScopeMeter test tools have three input channels that are electrically floating with respect to each other, and with respect to the power adapter input. Channel A and channel B are Oscilloscope channels with a 60/100/200 MHz bandwidth. The Meter/External Trigger channel is a combined DMM and external trigger channel with a limited (20 kHz) bandwidth.

show more

User Manual
Manual type:
User Manual
Pages:
116
Size:
2.29 Mbytes (2403431 Bytes)
Language:
english
Revision:
Rev.2, 2/01
Manual-ID:
4822 872 00983
Date:
unknown
Quality:
Electronic document, no scan, very well readable.
Upload date:
2008 11 03
MD5:
7a0c3f46114d08926ed88125214e4e2b
Downloads:
3657
User Manual Supplement
Manual type:
User Manual Supplement
Pages:
2
Size:
124.09 Kbytes (127067 Bytes)
Language:
english
Revision:
Manual-ID:
Date:
unknown
Quality:
Electronic document, no scan, very well readable.
Upload date:
2016 01 27
MD5:
11d3d69a3ab158e3e927bfeefbe708f2
Downloads:
1606
Service Manual
Manual type:
Service Manual
Pages:
206
Size:
7.80 Mbytes (8180057 Bytes)
Language:
english
Revision:
2
Manual-ID:
4822 672 05376
Date:
2000 03 01
Quality:
Scanned document, all readable.
Upload date:
2018 01 08
MD5:
69a9d171f14ebbb590ad02c12cb59f8e
Downloads:
1658

Information

1.1 Introduction ... 1-3 1.2 Safety Precautions ... 1-3 1.3 Caution and Warning Statements ... 1-3 1.4 Symbols ... 1-3 1.5 Impaired Safety ... 1 -4 ' 1.6 General Safety Information ... 1-4 2 Characteristics ... 2-1 2.1 Introduction ... 2-3 2.2 Dual Input Oscilloscope ... 2-3 2.2.1 Isolated Inputs A and B (Vertical) ... 2-3 2.2.2 Horizontal ... 2-4 2.2.3 Trigger and Delay ... 2-4 2.2.4 Automatic Connect&View Trigger ... 2-4 2.2.5 Edge Trigger ... 2-5 2.2.6 Isolated External Trigger ... 2-5 2.2.7 Video Trigger ... 2-5 2.2.8 Pulse Width Trigger ... 2-5 2.2.9 Continuous Auto Set ... 2-5 2.2.10 Automatic Capturing Scope Screens ... 2-6 2.3 Automatic Scope Measurements ... 2-6 2.3.1 General ... 2-6 2.3.2 DC Voltage (VDC) ... 2-6 2.3.3 AC Voltage (VAC) ... 2-6 2.3.4 AC+DC Voltage (True RMS) ... 2-7 2.3.5 Amperes (AMP) ... 2-7 2.3.6 Peak ... 2-7 2.3.7 Frequency (Hz) ... 2-8 2.3.8 Duty Cycle (DUTY) ... 2-8 2.3.9 Pulse Width (PULSE) ... 2-8 2.3.10 Power ... 2-8 2.3.11 Phase ... 2-8 2.3.12 Temperature (TEMP) ... 2-9 2.3.13 Decibel (dB) ... 2-9 2.4 Meter ... 2-9 2.4.1 Meter Input ... 2-9 2.4.2 Meter Functions ... 2-9 2.5 DMM Measurements on Meter Inputs ... 2-9 2.5.1 General ... 2-9 2.5.2 Ohms (£2) ... 2-10 2.5.3 Continuity (CONT) ... 2-10 2.5.4 Diode ... 2-10 2.5.5 Temperature (TEMP) ... 2-10 2.5.6 DC Voltage (VDC) ... 2-10 2.5.7 AC Voltage (VAC) ... 2-11 2.5.8 AC+DC Voltage (True RMS) ... 2-11 2.5.9 Amperes (AMP) ... 2-11 2.6 Recorder ... 2-11 2.6.1 TrendPlot (Meter or Scope) ... 2-11 2.6.2 Scope Record ... 2-12 2.7 Zoom, Replay and Cursors ... 2-12 2.7.1 Zoom ... 2-12 2.7.2 Replay ... 2-12 2.7.3 Cursor Measurements ... 2-12 2.8 Miscellaneous ... 2-13 2.8.1 Display ... 2-13 7. .8.7 /l Power ... 2-13 2.8.3 Probe Calibration ... 2-13 2.8.4 Memory ... 2-13 2.8.5 Mechanical ... 2-13 2.8.6 Optical Interface Port ... 2-14 2.9 Environmental ... 2-14 2.10 Zh Safety ... 2-14 2.11 10:1 probe ... 2-16 2.11.1 Safety ... 2-16 2.11.2 Electrical specifications ... 2-16 2.11.3 Environmental ... 2-16 2.12 Electromagnetic Immunity ... 2-17 3 Circuit Description ... 3-1 3.1 Introduction ... 3-3 3.2 Block Diagram ... 3-3 3.3 Start-up Sequence, Operating Modes ... 3-7 3.4 Detailed Circuit Descriptions ... 3-9 3.4.1 Scope Channel A - Scope Channel B ... 3-9 3.4.2 Meter/Ext Trigger Channel ... 3-12 3.4.3 Sampling&Triggering (S-ASIC) ... 3-14 3.4.4 S-ASIC supply ... 3-19 3.4.5 ADC’s ... 3-19 3.4.6 Digital Control ... 3-19 3.4.7 Power ... 3-24 3.4.8 Slow ADC, RS232 Serial Interface, Backlight, Buzzer ... 3-28 4 Performance Verification ... 4-1 4.1 Introduction ... 4-3 4.2 Equipment Required For Verification ... 4-3 4.3 General Instructions ... 4-3 4.4 Operating Instructions ... 4-4 4.4.1 Resetting the test tool ... 4-4 4.4.2 Navigating through menu’s ... 4-4 4.4.3 Creating Test Tool Setup 1 ... 4-5 4.5 Display and Backlight Test ... 4-5 4.6 Scope Input A&B Tests ... 4-7 4.6.1 Input A&B Vertical Accuracy Test ... 4-7 4.6.2 Input A&B DC Voltage Accuracy Test ... 4-9 4.6.3 Input A&B AC Voltage Accuracy Test (LF) ... 4-11 4.6.4 Input A&B AC Coupled Lower Frequency Test ... 4-12 4.6.5 Input A and B Peak Measurements Test ... 4-13 4.6.6 Input A&B Frequency Measurement Accuracy Test ... 4-14 4.6.7 Input A&B Phase Measurements Test ... 4-15 4.6.8 Time Base Test ... 4-16 4.6.9 Input A Trigger Sensitivity Test ... 4-18 4.6.10 Input A AC Voltage Accuracy (HF) & Bandwidth Test ... 4-19 4.6.11 Input B Trigger Sensitivity Test ... 4-20 4.6.12 Input B AC Voltage Accuracy (HF) & Bandwidth Test ... 4-21 4.6.13 Video test ... 4-22 4.7 External Trigger Level Test ... 4-26 4.8 Meter (DMM) Tests ... 4-27 4.8.1 Meter DC Voltage Accuracy Test ... 4-27 4.8.2 Meter AC Voltage Accuracy & Frequency Response Test ... 4-28 4.8.3 Continuity Function Test ... 4-29 4.8.4 Diode Test Function Test ... 4-29 4.8.5 Ohms Measurements Test ... 4-29 4.9 Probe Calibration Generator Test ... 4-31 5 Calibration Adjustment ... 5-1 5.1 General ... 5-3 5.1.1 Introduction ... 5-3 5.1.2 Calibration number and date ... 5-3 5.1.3 General Instructions ... 5-3 5.1.4 Equipment Required For Calibration ... 5-4 5.2 Calibration Procedure Steps ... 5-4 5.3 Starting the Calibration ... 5-4 5.4 Contrast Calibration Adjustment ... 5-6 5.5 Warming Up & Pre-Calibration ... 5-7 5.6 Final Calibration ... 5-8 5.6.1 Input A LF-HF Gain ... 5-8 5.6.2 Input B LF-HF Gain ... 5-9 5.6.3 Input A&B LF-HF Gain ... 5-11 5.6.4 Input A&B Position ... 5-12 5.6.5 Input A&B Volt Gain ... 5-12 5.6.6 DMM Volt Gain ... 5-14 5.6.7 Input A& B, and DMM Zero ... 5-15 5.6.8 DMM Ohm Gain ... 5-15 5.6.9 Calculate Gain ... 5-16 5.7 Save Calibration Data and Exit ... 5-17 5.8 Probe Calibration ... 5-18 6 Disassembling the Test Tool ... 6-1 6.1. Introduction ... 6-3 6.2. Disassembly & Reassembly Procedures ... 6-3 6.2.1 Required Tools ... 6-3 6.2.2 Removing the Tilt Stand & Hang Strap ... 6-3 6.2.3 Replacing the Side-Strap, Changing the Side-Strap Position ... 6-3 6.2.4 Opening the Test Tool, Removing the Battery ... 6-3 6.2.5 Removing the Main PCA Unit ... 6-5 6.2.6 Removing the Display Assembly ... 6-6 6.2.7 Removing the Keypad and Keypad Foil ... 6-6 6.2.8 Disassembling the Main PCA Unit ... 6-7 6.2.9 Reassembling the Main PCA Unit ... 6-8 6.2.10 Reassembling the Test Tool ... 6-8 7 Corrective Maintenance ... 7-1 7.1 Introduction ... 7-3 7.2 Starting Fault Finding ... 7-4 7.3 Charger Circuit ... 7-5 7.4 Starting with a Dead Test Tool ... 7-6 7.4.1 Test Tool Completely Dead ... 7-7 7.4.2 Test Tool Software Does not Run ... 7-7 7.4.3 Software Runs, Test Tool not Operative ... 7-8 7.5 Miscellaneous Functions ... 7-8 7.5.1 Display and Back Light ... 7-8 7.5.2 Fly Back Converter ... 7-9 7.5.3 Slow ADC, +3V3SADC ... 7-10 7.5.4 Keyboard ... 7-11 7.5.5 Optical Port (Serial RS232 Interface) ... 7-12 7.5.6 Channel A, Channel B Measurements ... 7-12 7.5.7 Meter Channel (Ext Trigger, Probe Cal) ... 7-13 7.5.8 Input Signal Acquisition ... 7-16 7.5.9 ADC’s ... 7-18 7.5.10 Digital Control & Memory ... 7-19 7.5.11 Buzzer Circuit ... 7-20 7.5.12 RAM Test ... 7-20 7.5.13 Power ON/OFF ... 7-21 7.6 Loading Software ... 7-21 8 List of Replaceable Parts ... 8-1 8.1 Introduction ... 8-3 8.2 How to Obtain Parts ... 8-3 8.3 Service Centers ... 8-3 8.4 Final Assembly Parts ... 8-4 8.5 Main PCA Unit Parts ... 8-6 8.6 Main PCA Parts ... 8-8 8.7 Accessories ... 8-26 9 Circuit Diagrams ... 9-1 9.1 Introduction ... 9-3 9.2 Tracing signals in circuit diagrams ... 9-3 9.3 Locating Parts & Test Points ... 9-3 9.4 Diagrams ... 9-10 10 Modifications ... 10-1 10.1 Software modifications ... 10-3

show more

Add Comment

* Required information

Comments

No comments yet. Be the first!